ZHCSAD5A October   2012  – December 2014

PRODUCTION DATA.  

1. 1 特性
2. 2 應用
3. 3 說明
4. 4 修訂歷史記錄
5. 5 說明（續(xù)）
6. 6 Pin Configuration and Functions
7. 7 Specifications
   1. 7.1 Absolute Maximum Ratings
   2. 7.2 ESD Ratings
   3. 7.3 Recommended Operating Conditions
   4. 7.4 Thermal Information
   5. 7.5 Electrical Characteristics
   6. 7.6 Typical Characteristics
8. 8 Detailed Description
   1. 8.1 Overview
   2. 8.2 Functional Block Diagram
   3. 8.3 Feature Description
      1. 8.3.1 Device Power Up
         1. 8.3.1.1 Power-On-Reset (POR)
         2. 8.3.1.2 Power Up from Battery without DC Source
            1. 8.3.1.2.1 BATFET Turn Off
            2. 8.3.1.2.2 Shipping Mode
         3. 8.3.1.3 Power Up from DC Source
            1. 8.3.1.3.1 REGN LDO
            2. 8.3.1.3.2 Input Source Qualification
            3. 8.3.1.3.3 Input Current Limit Detection
            4. 8.3.1.3.4 PSEL/OTG Pins Set Input Current Limit
            5. 8.3.1.3.5 HIZ State wth 100mA USB Host
            6. 8.3.1.3.6 Force Input Current Limit Detection
         4. 8.3.1.4 Converter Power-Up
         5. 8.3.1.5 Boost Mode Operation from Battery
      2. 8.3.2 Power Path Management
         1. 8.3.2.1 Narrow VDC Architecture
         2. 8.3.2.2 Dynamic Power Management
         3. 8.3.2.3 Supplement Mode
      3. 8.3.3 Battery Charging Management
         1. 8.3.3.1 Autonomous Charging Cycle
         2. 8.3.3.2 Battery Charging Profile
         3. 8.3.3.3 Thermistor Cold/Hot Temperature Window
         4. 8.3.3.4 Charging Termination
            1. 8.3.3.4.1 Termination when REG02[0] = 1
            2. 8.3.3.4.2 Termination when REG05[6] = 1
         5. 8.3.3.5 Charging Safety Timer
         6. 8.3.3.6 USB Timer when Charging from USB100mA Source
      4. 8.3.4 Status Outputs (PG, STAT, and INT)
         1. 8.3.4.1 Power Good Indicator (PG)
         2. 8.3.4.2 Charging Status Indicator (STAT)
         3. 8.3.4.3 Interrupt to Host (INT)
      5. 8.3.5 Protections
         1. 8.3.5.1 Input Current Limit on ILIM
         2. 8.3.5.2 Thermal Regulation and Thermal Shutdown
         3. 8.3.5.3 Voltage and Current Monitoring in Buck Mode
            1. 8.3.5.3.1 Input Over-Voltage (ACOV)
            2. 8.3.5.3.2 System Over-Voltage Protection (SYSOVP)
         4. 8.3.5.4 Voltage and Current Monitoring in Boost Mode
            1. 8.3.5.4.1 VBUS Over-Voltage Protection
         5. 8.3.5.5 Battery Protection
            1. 8.3.5.5.1 Battery Over-Current Protection (BATOVP)
            2. 8.3.5.5.2 Charging During Battery Short Protection
            3. 8.3.5.5.3 System Over-Current Protection
      6. 8.3.6 Serial Interface
         1. 8.3.6.1 Data Validity
         2. 8.3.6.2 START and STOP Conditions
         3. 8.3.6.3 Byte Format
         4. 8.3.6.4 Acknowledge (ACK) and Not Acknowledge (NACK)
         5. 8.3.6.5 Slave Address and Data Direction Bit
            1. 8.3.6.5.1 Single Read and Write
            2. 8.3.6.5.2 Multi-Read and Multi-Write
   4. 8.4 Device Functional Modes
      1. 8.4.1 Host Mode and Default Mode
         1. 8.4.1.1 Plug in USB100mA Source with Good Battery
         2. 8.4.1.2 USB Timer when Charging from USB 100-mA Source
   5. 8.5 Register Map
      1. 8.5.1 I2C Registers
         1. 8.5.1.1  Input Source Control Register REG00 (reset = 00110000, or 30)
         2. 8.5.1.2  Power-On Configuration Register REG01 (reset = 00011011, or 1B)
         3. 8.5.1.3  Charge Current Control Register REG02 (reset = 01100000, or 60)
         4. 8.5.1.4  Pre-Charge/Termination Current Control Register REG03 (reset = 00010001, or 11)
         5. 8.5.1.5  Charge Voltage Control Register REG04 (reset = 11001010, or CA)
         6. 8.5.1.6  Charge Termination/Timer Control Register REG05 (reset = 10011010, or 9A)
         7. 8.5.1.7  Thermal Regulation Control Register REG06 (reset = 00000011, or 03)
         8. 8.5.1.8  Misc Operation Control Register REG07 (reset = 01001011, or 4B)
         9. 8.5.1.9  System Status Register REG08
         10. 8.5.1.10 Fault Register REG09
         11. 8.5.1.11 Vender / Part / Revision Status Register REG0A (reset = 00101011, or 2B)
9. 9 Application and Implementation
   1. 9.1 Application Information
   2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
         1. 9.2.2.1 Inductor Selection
         2. 9.2.2.2 Input Capacitor
         3. 9.2.2.3 Output Capacitor
      3. 9.2.3 Application Performance Plots
10. 10Power Supply Recommendations
11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
12. 12器件和文檔支持
    1. 12.1 文檔支持
       1. 12.1.1 相關文檔
    2. 12.2 商標
    3. 12.3 靜電放電警告
    4. 12.4 術語表
13. 13機械、封裝和可訂購信息