SLVS551A December 2004 – September 2015 TPS65014
PRODUCTION DATA.
- 1 Features
- 2 Applications
- 3 Description
- 4 Revision History
- 5 Pin Configuration and Functions
-
6 Specifications
- 6.1 Absolute Maximum Ratings
- 6.2 ESD Ratings
- 6.3 Recommended Operating Conditions
- 6.4 Thermal Information
- 6.5 Electrical Characteristics
- 6.6 Electrical Characteristics: Battery Charger
- 6.7 Dissipation Ratings
- 6.8 Serial Interface Timing Requirements
- 6.9 Switching Characteristics
- 6.10 Typical Characteristics
-
7 Detailed Description
- 7.1 Overview
- 7.2 Functional Block Diagram
- 7.3 Feature Description
- 7.4 Device Functional Modes
- 7.5
Register Maps
- 7.5.1 CHGSTATUS Register (offset = 01h) (reset: 00h)
- 7.5.2 REGSTATUS Register (offset = 02h) (reset: 00h)
- 7.5.3 MASK1 Register (offset = 03h) (reset: FFh)
- 7.5.4 MASK2 Register (offset = 04h) (reset: FFh)
- 7.5.5 ACKINT1 Register (offset = 05h) (reset: 00h)
- 7.5.6 ACKINT2 Register (offset: 06h) (reset: 00h)
- 7.5.7 CHGCONFIG Register (offset: 07h) (reset: 1Bh)
- 7.5.8 LED1_ON Register (offset: 08h) (reset: 00h)
- 7.5.9 LED1_PER Register (offset: 09h) (reset: 00h)
- 7.5.10 LED2_ON Register (offset: 0Ah) (reset: 00h)
- 7.5.11 LED2_PER (offset: 0Bh) (reset: 00h)
- 7.5.12 VDCDC1 Register (offset: 0Ch) (reset: 32h/33h)
- 7.5.13 VDCDC2 Register (offset: 0Dh) (reset: 60h/70h)
- 7.5.14 VREGS1 Register (offset: 0Eh) (reset: 88h)
- 7.5.15 MASK3 Register (offset: 0Fh) (reset: 00h)
- 7.5.16 DEFGPIO Register (offset = 10h) (reset: 00h)
- 8 Application and Implementation
- 9 Power Supply Recommendations
- 10Layout
- 11Device and Documentation Support
- 12Mechanical, Packaging, and Orderable Information
封裝選項
機械數據 (封裝 | 引腳)
- RGZ|48
散熱焊盤機械數據 (封裝 | 引腳)
- RGZ|48
訂購信息
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range unless otherwise noted(1)| MIN | MAX | UNIT | |
|---|---|---|---|
| Input voltage on VAC pin with respect to AGND | 20 | V | |
| Input voltage range on all other pins except AGND/PGND pins with respect to AGND | –0.3 | 7 | V |
| Current at AC, VBAT, VINMAIN, L1, PGND1 | 1800 | mA | |
| Peak current at all other pins | 1000 | mA | |
| Continuous power dissipation | See Dissipation Ratings | ||
| Operating free-air temperature, TA | –40 | 85 | °C |
| Maximum junction temperature, TJ | 125 | °C | |
| Storage temperature, Tstg | –65 | 150 | °C |
| Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds | 260 | °C |
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
| VALUE | UNIT | |||
|---|---|---|---|---|
| V(ESD) | Electrostatic discharge | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)(3) | ±1000 | V |
| Charged-device model (CDM), per JEDEC specification JESD22-C101(2)(3) | ±1000 | |||
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with less than 500-V HBM is possible with the necessary precautions. Pins listed as ±1000 V may actually have higher performance.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Manufacturing with less than 250-V CDM is possible with the necessary precautions. Pins listed as ±1000 V may actually have higher performance.
(3) At pins VIB, PG, and LED2
6.3 Recommended Operating Conditions
| MIN | NOM | MAX | UNIT | ||
|---|---|---|---|---|---|
| V(AC) | Supply voltage from AC adapter | 4.5 | 6.5 | V | |
| V(USB) | Supply voltage from USB | 4.4 | 5.25 | V | |
| V(BAT) | Voltage at battery | 2.5 | 4.2 | V | |
| VI(MAIN),VI(CORE),VCC | Input voltage range step-down converters | 2.5 | 6.0 | V | |
| VI(LDO1), VI(LDO2) | Input voltage range for LDOs | 1.8 | 6.5 | V | |
| TA | Operating ambient temperature | -40 | 85 | °C | |
| TJ | Operating junction temperature | -40 | 125 | °C | |
| R(CC) | Resistor from VI(main),VI(core) to VCC used for filtering, CI(VCC) = 1 µF | 10 | 100 | Ω | |
6.4 Thermal Information
| THERMAL METRIC(1) | TPS65014 | UNIT | |
|---|---|---|---|
| RGZ (VQFN) | |||
| 48 PINS | |||
| RθJA | Junction-to-ambient thermal resistance | 27.0 | °C/W |
| RθJC(top) | Junction-to-case (top) thermal resistance | 14.3 | °C/W |
| RθJB | Junction-to-board thermal resistance | 4.6 | °C/W |
| ψJT | Junction-to-top characterization parameter | 0.2 | °C/W |
| ψJB | Junction-to-board characterization parameter | 4.6 | °C/W |
| RθJC(bot) | Junction-to-case (bottom) thermal resistance | 1.1 | °C/W |
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953.
6.5 Electrical Characteristics
VI(MAIN) = VI(CORE) = VCC = VI(LDO1) = VI(LDO2) = 3.6 V, TA = –40°C to 85°C, typical values are at TA = 25°C battery charger specifications are valid in the range 0°C < TA < 85°C unless otherwise noted| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | ||
|---|---|---|---|---|---|---|---|
| CONTROL SIGNALS: LOW_PWR, SCLK, SDAT (INPUT) | |||||||
| VIH | High-level input voltage | IIH = 20 µA (1) | 2 | VCC | V | ||
| VIL | Low-level input voltage | IIL = 10 µA | 0 | 0.8 | V | ||
| IIB | Input bias current | 0.01 | 1 | µA | |||
| CONTROL SIGNALS: PB_ONOFF, HOT_RESET, BATT_COVER | |||||||
| VIH | High-level input voltage | IIH = 20 µA(1) | 0.8 VCC | 6 | V | ||
| VIL | Low-level input voltage | IIL = 10 µA | 0 | 0.4 | V | ||
| R(pb_onoff) | Pulldown resistor at PB_ONOFF | 1000 | kΩ | ||||
| R(hot_reset) | Pullup resistor at HOT_RESET, connected to VCC |
1000 | kΩ | ||||
| R(batt_cover) | Pulldown resistor at BATT_COVER | 2000 | kΩ | ||||
| CONTROL SIGNALS: MPU_RESET, PWRFAIL, RESPWRON, INT, SDAT (OUTPUT) | |||||||
| VOH | High-level output voltage | 6 | V | ||||
| VOL | Low-level output voltage | IIL = 10 mA | 0 | 0.3 | V | ||
| SUPPLY PIN: VCC | |||||||
| I(Q) | Operating quiescent current | VI = 3.6 V, current into Main + Core + VCC | 70 | µA | |||
| IO(SD) | Shutdown supply current | VI = 3.6 V, BATT_COVER = GND, Current into Main + Core + VCC |
15 | 25 | µA | ||
| VMAIN STEP-DOWN CONVERTER | |||||||
| VI | Input voltage range | 2.5 | 6 | V | |||
| IO | Maximum output current | 1000 | mA | ||||
| IO(SD) | Shutdown supply current | BATT_COVER = GND | 0.1 | 1 | µA | ||
| rDS(on) | P-channel MOSFET on-resistance | VI(MAIN) = VGS = 3.6 V | 110 | 210 | mΩ | ||
| Ilkg(p) | P-channel leakage current | V(DS) = 6 V | 1 | µA | |||
| rDS(on) | N-channel MOSFET on-resistance | VI(MAIN) = VGS = 3.6 V | 110 | 200 | mΩ | ||
| Ilkg(N) | N-channel leakage current | V(DS) = 6 V | 1 | µA | |||
| IL | P-channel current limit | 2.5 V< VI(MAIN) < 6 V | 1.4 | 1.75 | 2.1 | A | |
| fS | Oscillator frequency | 1 | 1.25 | 1.5 | MHz | ||
| VO(MAIN) | Fixed output voltage | 2.5 V | VI(MAIN) = 2.7 V to 6 V; IO = 0 mA | 0% | 3% | ||
| VI(MAIN) = 2.7 V to 6 V; 0 mA ≤ IO ≤ 1000 mA |
3% | 3% | |||||
| 2.75 V | VI(MAIN) = 2.95 V to 6 V; IO = 0 mA | 0% | 3% | ||||
| VI(MAIN) = 2.95 V to 6 V; 0 mA ≤ IO ≤ 1000 mA |
3% | 3% | |||||
| 3.0 V | VI(MAIN) = 3.2 V to 6 V; IO= 0 mA | 0% | 3% | ||||
| VI(MAIN) = 3.2 V to 6 V; 0 mA ≤ IO ≤ 1000 mA |
3% | 3% | |||||
| 3.3 V | VI(MAIN) = 3.5 V to 6 V; IO= 0 mA | 0% | 3% | ||||
| VI(MAIN) = 3.5 V to 6 V; 0 mA ≤ IO ≤ 1000 mA |
3% | 3% | |||||
| Line regulation | VI(MAIN) = VO(MAIN) + 0.5 V (min. 2.5 V) to 6 V, IO = 10 mA |
0.5 | %/V | ||||
| Load regulation | IO = 10 mA to 1000 mA | 0.12 | %/A | ||||
| R(VMAIN) | VMAIN discharge resistance | 400 | Ω | ||||
| VCORE STEP-DOWN CONVERTER | |||||||
| VI | Input voltage range | 2.5 | 6 | V | |||
| IO | Maximum output current | 400 | mA | ||||
| IO(SD) | Shutdown supply current | BATT_COVER = GND | 0.1 | 1 | µA | ||
| rDS(on) | P-channel MOSFET on-resistance | VI(CORE) = VGS = 3.6 V | 275 | 530 | mΩ | ||
| Ilkg(p) | P-channel leakage current | VDS = 6 V | 0.1 | 1 | µA | ||
| rDS(on) | N-channel MOSFET on-resistance | VI(CORE) = VGS = 3.6 V | 275 | 500 | mΩ | ||
| Ilkg(N) | N-channel leakage current | VDS = 6 V | 0.1 | 1 | µA | ||
| IL | P-channel current limit | 2.5 V < VI(CORE) < 6 V | 600 | 700 | 900 | mA | |
| fS | Oscillator frequency | 1 | 1.25 | 1.5 | MHz | ||
| VCORE STEP-DOWN CONVERTER (continued) | |||||||
| VO(CORE) | Fixed output voltage | 0.85 V | VI(CORE) = 2.5 V to 6 V; IO = 0 mA, CO = 22 µF |
0% | 3% | ||
| VI(CORE) = 2.5 V to 6 V; 0 mA ≤ IO ≤ 400 mA, CO = 22 µF |
3% | 3% | |||||
| 1.0 V | VI(CORE) = 2.5 V to 6 V; IO = 0 mA, CO = 22 µF |
0% | 3% | ||||
| VI(CORE) = 2.5 V to 6 V; 0 mA ≤ IO ≤ 400 mA, CO = 22 µF |
3% | 3% | |||||
| 1.1 V | VI(CORE) = 2.5 V to 6 V; IO= 0 mA, CO = 22 µF |
0% | 3% | ||||
| VI(CORE) = 2.5 V to 6 V; 0 mA ≤ IO ≤ 400 mA, CO = 22 µF |
3% | 3% | |||||
| 1.2 V | VI(CORE) = 2.5 V to 0 V; IO = 0 mA | 0% | 3% | ||||
| VI(CORE) = 2.5 V to 6 V; 0 mA ≤ IO≤ 400 mA | 3% | 3% | |||||
| 1.3 V | VI(CORE) = 2.5 V to 6 V; IO= 0 mA | 0% | 3% | ||||
| VI(CORE) = 2.5 V to 6 V; 0 mA ≤ IO ≤ 400 mA |
3% | 3% | |||||
| 1.4 V | VI(CORE) = 2.5 V to 6 V; IO= 0 mA | 0% | 3% | ||||
| VI(CORE) = 2.5 V to 6 V; 0 mA ≤ IO≤ 400 mA |
3% | 3% | |||||
| 1.5 V | VI(CORE) = 2.5 V to 6 V; IO = 0 mA | 0% | 3% | ||||
| VI(CORE) = 2.5 V to 6 V; 0 mA ≤ IO ≤ 400 mA |
3% | 3% | |||||
| 1.8 V | VI(CORE) = 2.5 V to 6 V; IO= 0 mA | 0% | 3% | ||||
| VI(CORE) = 2.5 V to 6 V; 0 mA ≤ IO ≤ 400 mA |
3% | 3% | |||||
| Line regulation | VI(CORE) = VO(MAIN) + 0.5 V (min. 2.5 V) to 6 V, IO = 10 mA |
1 | %/V | ||||
| Load regulation | IO = 10 mA to 400 mA | 0.002 | %/mA | ||||
| R(VCORE) | VCORE discharge resistance | 400 | Ω | ||||
| VLDO1 and VLDO2 LOW-DROPOUT REGULATORS | |||||||
| VI | Input voltage range | LD01 | 1.8 | 6.5 | V | ||
| LD02 | 1.8 | VCC | |||||
| VO | LDO1 output voltage range | 0.9 | VINLDO1 | V | |||
| Vref | Reference voltage | 485 | 500 | 515 | mV | ||
| VO | LDO2 output voltage range | 1.8 | 3.3 | V | |||
| IO | Maximum output current | Full-power mode | 200 | mA | |||
| Low-power mode | 30 | ||||||
| I(SC) | LDO1 and LDO2 short-circuit current limit | VLDO1 = GND, VLDO2 = GND | 650 | mA | |||
| Dropout voltage | IO = 200 mA, VINLDO1,2 = 1.8 V | 300 | mV | ||||
| Total accuracy | ±3% | ||||||
| Line regulation | VINLDO1,2 = VLDO1,2 + 0.5 V (min. 2.5 V) to 6.5 V, IO = 10 mA |
0.75 | %/V | ||||
| Load regulation | IO = 10 mA to 200 mA | 0.011 | %/mA | ||||
| Regulation time | Load change from 10% to 90% | 0.1 | ms | ||||
| Low-power mode | 0.1 | ||||||
| I(QFP) | LDO quiescent current (each LDO) | Full-power mode | 16 | 30 | µA | ||
| I(QLPM) | LDO quiescent current (each LDO) | Low-power mode | 12 | 18 | µA | ||
| IO(SD) | LDO shutdown current (each LDO) | 0.1 | 1 | µA | |||
| Ilkg(FB) | Leakage current feedback | 0.01 | 0.1 | µA | |||
(1) If the input voltage is higher than VCC, an additional input current, limited by an internal 10-kΩ resister, flows.
6.6 Electrical Characteristics: Battery Charger
VO(REG) + V(DO-MAX) ≤ V(CHG) = V(AC) or V(USB), I(TERM) < IO ≤ 1 A, 0°C < TA < 85°C| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | ||
|---|---|---|---|---|---|---|---|
| VLDO1 and VLDO2 LOW-DROPOUT REGULATORS (continued) | |||||||
| V(AC) | Input voltage range | 4.5 | 6.5 | V | |||
| V(USB) | Input voltage range | 4.35 | 5.25 | V | |||
| ICC(VCHG) | Supply current | V(CHG) > V(CHG)min | 1.2 | 2 | mA | ||
| ICC(SLP) | Sleep current | Sum of currents into VBAT pin, V(CHG) < V(SLP-ENTRY), 0°C ≤ TJ ≤ 85°C |
2 | 5 | µA | ||
| ICC(STBY) | Standby current | Current into USB pin | 45 | µA | |||
| Current into AC pin | 200 | 400 | |||||
| VOLTAGE REGULATOR | |||||||
| VO | Output voltage | V(CHG)min ≥ 4.5 V | 4.15 | 4.20 | 4.25 | V | |
| VDO | Dropout voltage (V(AC) – VBAT) | VO(REG) + V(DO-MAX) ≤ V(CHG), IO(OUT) = 1 A |
500 | 800 | mV | ||
| Dropout voltage (V(USB) – VBAT) | VO(REG) + V(DO-MAX)≤ V(CHG), IO(OUT) = 0.5 A |
300 | 500 | ||||
| Dropout voltage (V(USB) – VBAT) | VO(REG) + V(DO-MAX) ≤ V(CHG), IO(OUT) = 0.1 A |
100 | 150 | ||||
| CURRENT REGULATION | |||||||
| IO(AC) | Output current range for ac operation(1) | VCHG ≥ 4.5 V, VI(OUT) > V(LOWV), V(AC) - VI(BAT)> V(DO-MAX) |
100 | 1000 | mA | ||
| V(SET) | Output current set voltage for ac operation at ISET pin. 100% output current I2C register CHGCONFIG<4:3> = 11 | Vmin ≥ 4.5 V, VI(BAT) > V(LOWV), V(AC) - VI(BAT) > V(DO-MAX) | 2.45 | 2.50 | 2.55 | V | |
| 75% output current I2C register CHGCONFIG<4:3> = 10 | 1.83 | 1.91 | 1.99 | ||||
| 50% output current I2C register CHGCONFIG<4:3> = 01 | 1.23 | 1.31 | 1.39 | ||||
| 32% output current I2C register CHGCONFIG<4:3> = 00 | 0.76 | 0.81 | 0.86 | ||||
| KSET | Output current set factor for ac operation | 100 mA < IO < 1000 mA | 310 | 330 | 350 | ||
| 10 mA < IO < 100 mA | 300 | 340 | 380 | ||||
| IO(USB) | Output current range for USB operation | V(CHG)min ≥ 4.35 V, VI(BAT) > V(LOWV), V(USB) - VI(BAT) > V(DO-MAX),
I2C register CHGCONFIG<2> = 0 |
80 | 100 | mA | ||
| V(CHG)min ≥ 4.5 V, VI(BAT) > V(LOWV), VUSB - VI(BAT) > V(DO-MAX),
I2C register CHGCONFIG<2> = 1 |
400 | 500 | |||||
| R(ISET) | Resistor range at ISET pin | 825 | 8250 | Ω | |||
| PRECHARGE CURRENT REGULATION, SHORT-CIRCUIT CURRENT, AND BATTERY DETECTION CURRENT | |||||||
| V(LOWV) | Precharge to fast-charge transition threshold, voltage on VBAT pin. |
V(CHG) min ≥ 4.5 V | 2.8 | 3 | 3.2 | V | |
| I(PRECHG) | Precharge current (2) | 0 ≤ VI(OUT) < V(LOWV), t < t(PRECHG) | 10 | 100 | mA | ||
| I(DETECT) | Battery detection current | 200 | µA | ||||
| V(SET-PRECHG) | Voltage at ISET pin | 0 ≤ VI(OUT) < V(LOWV), t < t(PRECHG) | 240 | 255 | 270 | mV | |
| CHARGE TAPER AND TERMINATION DETECTION | |||||||
| I(TAPER) | Taper current detect range (3) | VI(OUT) > V(RCH), t < t(TAPER) | 10 | 100 | mA | ||
| V(SET_TAPER) | Voltage at ISET pin for charge TAPER detection | VI(OUT) > V(RCH), t < t(TAPER) | 235 | 250 | 265 | mV | |
| V(SET_TERM) | Voltage at ISET pin for charger termination detection(4) |
VI(OUT) > V(RCH) | 11 | 18 | 25 | mV | |
| TEMPERATURE COMPARATOR | |||||||
| V(LTF) | Low (cold) temperature threshold | 2.475 | 2.50 | 2.525 | V | ||
| V(HTF) | High (hot) temperature threshold | 0.485 | 0.5 | 0.515 | V | ||
| I(TS) | TS current source | 95 | 102 | 110 | µA | ||
| BATTERY RECHARGE THRESHOLD | |||||||
| V(RCH) | Recharge threshold | V(CHG)min ≥ 4.5 V | VO(REG) – 0.115 | VO(REG) – 0.1 | VO(REG) – 0.085 | V | |
| SLEEP AND STANDBY | |||||||
| V(SLP-ENTRY) | Sleep-mode entry threshold, PG output = high |
2.3 V ≤ VI(OUT) ≤ VO(REG) | V(CHG)≤ VI(OUT) +150 mV | V | |||
| V(SLP_EXIT) | Sleep-mode exit threshold, PG output = low |
2.3 V ≤ VI(OUT)≤ VO(REG) | V(CHG) ≥ VI(OUT) + 250 mV |
V | |||
| CHARGER POWER-ON-RESET, UVLO, AND V(IN) RAMP RATE | |||||||
| V(CHGUVLO) | Charger undervoltage lockout | V(CHG) decreasing | 2.27 | 2.5 | 2.75 | V | |
| Hysteresis | 27 | mV | |||||
| V(CHGOVLO) | Charger overvoltage lockout | 6.5 | V | ||||
| CHARGER OVERTEMPERATURE SUSPEND | |||||||
| T(suspend) | Temperature at which charger suspends operation |
145 | °C | ||||
| T(hyst) | Hysteresis of suspend threshold | 20 | °C | ||||
| LOGIC SIGNALS DEFMAIN, DEFCORE, PS_SEQ, IFLSB | |||||||
| VIH | High-level input voltage | IIH = 20 µA | VCC – 0.5 | VCC | V | ||
| VIL | Low-level input voltage | IIL = 10 µA | 0 | 0.4 | V | ||
| IIB | Input bias current | 0.01 | 1 | µA | |||
| LOGIC SIGNALS GPIO1-4 | |||||||
| VOL | Low-level output voltage | IOL = 1 mA, configured as an open-drain output |
0.3 | V | |||
| VOH | High-level output voltage | Configured as an open-drain output | 6 | V | |||
| VIL | Low -level input voltage | 0 | 0.8 | V | |||
| VIH | High-level input voltage | 2 | VCC (5) | V | |||
| II | Input leakage current | 1 | µA | ||||
| rDS(on) | Internal NMOS | VOL = 0.3 V | 150 | Ω | |||
| LOGIC SIGNALS PG, LED2 | |||||||
| VOL | Low-level output voltage | IOL = 20 mA | 0.5 | V | |||
| VOH | High-level output voltage | 6 | V | ||||
| V(PG) | PG threshold voltage USB and AC | V(BAT) + xx mV | V | ||||
| VIBRATOR DRIVER VIB | |||||||
| VOL | Low-level output voltage | IOL = 100 mA | 0.3 | 0.5 | V | ||
| VOH | High-level output voltage | 6 | V | ||||
| THERMAL SHUTDOWN | |||||||
| T(SD) | Thermal shutdown | Increasing junction temperature | 160 | °C | |||
| UNDERVOLTAGE LOCKOUT | |||||||
| V(UVLO) | Undervoltage lockout threshold. The default value for UVLO is 2.75 V |
V(UVLO) 2.5 V | Filter resistor = 10R in series with VCC, VCC decreasing |
-3% | 3% | ||
| V(UVLO) 2.75 V | -3% | 3% | |||||
| V(UVLO) 3.0 V | -3% | 3% | |||||
| V(UVLO) 3.25 V | -3% | 3% | |||||
| V(UVLO_HYST) | UVLO comparator hysteresis | VCC rising | 350 | 400 | 450 | mV | |
| POWER GOOD | |||||||
| Decreasing rail voltage | VMAIN, VCORE, VLDO1, VLDO2 decreasing |
–12% | –10% | –8% | |||
| Increasing rail voltage | VMAIN, VCORE, VLDO1, VLDO2 increasing |
–7% | –5% | –3% | |||
(1) 
(2) 
(3) 
(4) 
(5) If the input voltage is higher than VCC an additional current flows, limited by an internal 10-kΩ resistor.
6.7 Dissipation Ratings
See (1)| AMBIENT TEMPERATURE |
MAX POWER DISSIPATION FOR Tj = 125°C(2) |
DERATING FACTOR ABOVE TA= 55°C |
|---|---|---|
| 25°C | 3 W | 30 mW/°C |
| 55°C | 2.1 W |
(1) The TPS65014 is housed in a 48-pin QFN package with exposed leadframe on the underside. This 7-mm × 7-mm package exhibits a thermal impedance (junction-to-ambient) of 33 K/W when mounted on a JEDEC high-k board.
(2) Consideration needs to be given to the maximum charge current when the assembled application board exhibits a thermal impedance which differs significantly from the JEDEC high-k board.
6.8 Serial Interface Timing Requirements
| MIN | MAX | UNIT | |
|---|---|---|---|
| Clock frequency, fMAX | 400 | kHz | |
| Clock high time, twH(HIGH) | 600 | ns | |
| Clock low time, twL(LOW) | 1300 | ns | |
| DATA and CLK rise time, tR | 300 | ns | |
| DATA and CLK fall time, tF | 300 | ns | |
| Hold time (repeated) START condition (after this period the first clock pulse is generated), th(STA) | 600 | ns | |
| Setup time for repeated START condition, th(DATA) | 600 | ns | |
| Data input hold time, th(DATA) | 0 | ns | |
| Data input setup time, tsu(DATA) | 100 | ns | |
| STOP condition setup time, tsu(STO) | 600 | ns | |
| Bus free time, t(BUF) | 1300 | ns |
6.9 Switching Characteristics
over operating free-air temperature range (unless otherwise noted)| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | |
|---|---|---|---|---|---|---|
| CONTROL SIGNALS: PB_ONOFF, HOT_RESET, BATT_COVER | ||||||
| t(glitch) | Deglitch time at all 3 pins | 38 | 56 | 77 | ms | |
| t(batt_cover) | Delay after t(glitch) (PWRFAIL goes low) before supplies are disabled when BATT_COVER goes low. | 1.68 | 2.4 | 3.2 | ms | |
| CONTROL SIGNALS: MPU_RESET, PWRFAIL, RESPWRON, INT, SDAT (OUTPUT) | ||||||
| td(mpu_nreset) | Duration of low pulse at MPU_RESET | 100 | µs | |||
| td(nrespwron) | Duration of low pulse at RESPWRON after VMAIN is in regulation | TPOR = 0 | 80 | 100 | 120 | ms |
| TPOR = 1 | 800 | 1000 | 1200 | |||
| td(uvlo) | Time between UVLO going active (PWRFAIL going low) and supplies being disabled | 1.68 | 2.4 | 3.2 | ms | |
| td(overtemp) | Time between chip overtemperature condition being recognized (PWRFAIL going low) and supplies being disabled | 1.68 | 2.4 | 3.2 | ms | |
| PRECHARGE CURRENT REGULATION, SHORT-CIRCUIT CURRENT, AND BATTERY DETECTION CURRENT | ||||||
| Deglitch time | V(CHG) min ≥ 4.5 V, VI(OUT) decreasing below threshold; 100-ns fall time, 10-mV overdrive | 8.8 | 23 | 60 | ms | |
| CHARGE TAPER AND TERMINATION DETECTION | ||||||
| Deglitch time for I(TAPER) | V(CHG) min ≥ 4.5V, charging current increasing or decreasing above and below; 100-ns fall time, 10-mV overdrive |
8.8 | 23 | 60 | ms | |
| Deglitch time for I(TERM) | V(CHG) min ≥ 4.5 V, charging current decreasing below;100-ns fall time, 10-mV overdrive | 8.8 | 23 | 60 | ms | |
| TEMPERATURE COMPARATOR | ||||||
| Deglitch time for temperature fault | 8.8 | 23 | 60 | ms | ||
| BATTERY RECHARGE THRESHOLD | ||||||
| Deglitch time | V(CHG)min ≥ 4.5 V, VI(OUT) decreasing below threshold; 100-ns fall time, 10-mV overdrive |
8.8 | 23 | 60 | ms | |
| TIMERS | ||||||
| t(PRECHG) | Precharge timer | V(CHG)min ≥ 4.5 V | 1500 | 1800 | 2160 | s |
| t(TAPER) | Taper timer | V(CHG)min ≥ 4.5 V | 1500 | 1800 | 2160 | s |
| t(CHG) | Charge timer | V(CHG)min ≥ 4.5 V | 15000 | 18000 | 21600 | s |
| SLEEP AND STANDBY | ||||||
| Deglitch time for sleep mode entry and exit | AC or USB decreasing below threshold; 100-ns fall time, 10-mV overdrive | 8.8 | 23 | 60 | ms | |
| t(USB_DEL) | Delay between valid USB voltage being applied and start of charging process from USB | 5 | ms | |||
6.10 Typical Characteristics
Table 1. Table of Graphs
| FIGURE | ||
|---|---|---|
| Efficiency | vs Output current | Figure 1, Figure 2 |
| Quiescent current | vs Input voltage | Figure 3 |
| Switching frequency | vs Temperature | Figure 4 |
| LDO1 Output voltage | vs Output current | Figure 5-Figure 8 |
| LDO2 Output voltage | vs Output current | Figure 9 |
| Line transient response (main) | Figure 9 | |
| Line transient response (core) | Figure 10 | |
| Line transient response (LDO1) | Figure 11 | |
| Line transient response (LDO2) | Figure 12 | |
| Load transient response (main) | Figure 13 | |
| Load transient response (core) | Figure 14 | |
| Load transient response (LDO1) | Figure 15 | |
| Load transient response (LDO2) | Figure 16 | |
| Output voltage ripple (PFM) | Figure 17 | |
| Output voltage ripple (PWM) | Figure 18 | |
| Start-up timing | Figure 19 | |
| Dropout voltage | vs Output current | Figure 20, Figure 21 |
| PSRR (LDO1 and LDO2) | vs Frequency | Figure 22 |
Figure 19. Start-Up Timing
