4 Revision History
Changes from Revision B (April 2019) to Revision C (September 2022)
- 刪除了標題中的“此器件的新版本現已上市：INA818”文本Go
- 通篇將最低電源電壓從 ±1.35V 更改為 ±2.25V，并從 2.7V 更改為 4.5VGo
- 更改了應用 以鏈接到 ti.com 上全新的終端設備Go
- 將最低電源電壓從 ±1.35V 更改成了 ±2.25VGo
- 將“簡化版原理圖”中的電阻器從 60kΩ 更改為 40kΩGo
- Changed minimum and maximum input common-mode voltage from
V– + 1.1 V and V+ – 1 V to V– + 2 V and
V+ – 2 V respectively in Recommended Operating
Conditions
Go
- Changed minimum and maximum ambient temperature from –55°C and
+150°C to –40°C and +125°C respectively in Recommended Operating
Conditions
Go
- Added VCM = 0 V to test conditions below title in
Electrical Characteristics
Go
- Changed input offset voltage vs temperature test condition from
TA = TMIN to TMAX to TA = –40°C
to +85°C in Electrical Characteristics
Go
- Changed input offset voltage vs power supply test condition from
VS = ±1.35 V to ±18 V to VS = ±2.25 V to ±18 V in
Electrical Characteristics
Go
- Changed high-side linear input voltage range from (V+) –
1 V minimum and (V+) – 0.65 V typical to (V+) – 2 V
minimum and (V+) – 1.4 V typical in Electrical
Characteristics
Go
- Changed low-side linear input voltage range from (V–) +
1.1 V minimum and (V–) + 0.95 V typical to (V–) + 2 V
minimum and (V–) + 1.2 V typical in Electrical
Characteristics
Go
- Added test condition of TA = –40°C to +85°C to bias
current vs temperature and offset current vs temperature in Electrical
Characteristics
Go
- Added test condition of TA = –40°C to +85°C to gain vs
temperature and 50-kΩ resistance vs temperature in Electrical
Characteristics
Go
- Changed single supply output voltage test condition from
VS = 2.7 V/0 V to V+ = 4.5 V, V– = 0 V in
Electrical Characteristics
Go
- Deleted power supply voltage range specification from Electrical
Characteristics
Go
- Deleted temperature range specifications from Electrical
Characteristics
Go
- Changed Figures 7-3, 7-4, 7-5, 7-6, 7-7, 7-8, 7-11, 7-12, 7-18,
7-19, and 7-20 in Typical Characteristics
Go
- Changed FET transistor input current limit from approximately 1.5-5
mA to 6 mA in Overview
Go
- Deleted internal node equations in Overview and Functional
Block Diagram
Go
- Changed schematic in Functional Block
Diagram
Go
- Changed linear input voltage range in Input Common-Mode Range
and Single-Supply Operation
Go
- Changed FET transistor input current limit from approximately 1.5-5
mA to 6 mA in Input Protection
Go
- Changed resistors in Figure 9-1 from 60 kΩ to 40 kΩ in Typical
Application
Go
- Changed minimum supply voltage from ±1.35 V to ±2.25 V in
Low-Voltage Operation
Go
- Changed minimum supply voltage from 2.7 V to 4.5 V in
Single-Supply Operation
Go
- Changed input common-mode range description in Single-Supply Operation
Go
- Changed Figure 10-5 to use a 5-V supply voltageGo
Changes from Revision A (January 2016) to Revision B (April 2019)
- 添加了有關升級后的新版本 INA818 的信息Go
- Added Device Comparison Table
Go
Changes from Revision * (September 2000) to Revision A (January 2016)
- 添加了 ESD 等級 表、特性說明 部分、器件功能模式 部分、應用和實現
部分、電源相關建議 部分、布局 部分、器件和文檔支持 部分以及機械、封裝和可訂購信息
部分。Go