Calculation tool
FET-INRUSH-SOA-CALC — FET SOA margin calculator for dvdt based startup
The design calculator allows user to estimate the FET SOA margin while starting up with dVdt based startup for inrush current control
LM74502H
3.2-V to 65-V industrial RPP controller with load disconnect, OVP, and high gate drive
Data sheet
LM74502H
- 3.2-V to 65-V input range (3.9-V start-up)
- –65-V input reverse voltage rating
- Integrated charge pump to drive
- External back-to-back N-Channel MOSFETs
-
External high side switch MOSFET
-
External reverse polarity protection MOSFET
- Gate drive variants
- LM74502: 60-μA peak gate drive source capacity
- LM74502H: 11-mA peak gate drive source capacity
- 2.3-A peak gate sink current capacity
- Enable pin feature
- 45-μA typical operating quiescent current (EN/UVLO = High)
- 1-μA shutdown current (EN/UVLO = Low)
- Adjustable overvoltage and undervoltage protection
- –40°C to +125°C ambient operating temperature range
- Available in 8-pin SOT-23 package 2.90 mm × 1.60 mm
The LM74502, LM74502H is a controller which operates in conjunction with an external back-to-back connected N-channel MOSFETs to realize a low loss reverse polarity protection and load disconnect solution. The device can also be configured to drive high side MOSFET as a load switch with overvoltage protection . The wide supply input range of 3.2 V to 65 V allows control of many popular DC bus voltages such as 12-V, 24-V and 48-V input systems. The device can withstand and protect the loads from negative supply voltages down to –65 V. The LM74502, LM74502H does not have reverse current blocking and is suitable for input reverse polarity protection only.
The LM74502 controller provides a charge pump gate drive for an external N-channel MOSFET. with the enable pin low, the controller is off and draws approximately 1 µA of current, thus offering low system current when put into sleep mode. LM74502 and LM74502H offers programmable overvoltage and undervoltage protection which cuts off the load from the input source in case of these fault events. The devices are available in a 2.9 mm × 1.6 mm 8-pin DDF package and are specified over a –40°C to +125°C temperature range.
Technical documentation
No results found. Please clear your search and try again.
View all 2 | Top documentation | Type | Title | Format options | Date |
|---|---|---|---|---|
| * | Data sheet | LM74502, LM74502H Low IQ High Side Switch Controller with Reverse Polarity and Overvoltage Protection datasheet (Rev. A) | PDF | HTML | 06 May 2022 |
| Application brief | Three Ways to Use High Side Switch Driver Using LM74502 | PDF | HTML | 20 Dec 2021 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
LM74502EVM — LM74502 and LM74502H evaluation module for ideal diode controller
LM74502EVM is an evaluation module for evaluating the performance of the ideal diode controller with switched output, LM74502 and LM74502H. The LM74502 ideal diode controllers drive and control external back-to-back N-channel MOSFETs to emulate an ideal diode rectifier with power path ON (...)
Simulation tool
PSPICE-FOR-TI — PSpice? for TI design and simulation tool
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Reference designs
PMP41115 — 240W integrated USB Type-C and USB PD3.1 charger reference design
This reference design is an integrated USB Type-C and USB power delivery (PD) charger for 10 to 12 cell batteries for applications such as e-bikes, high-capacity power banks, and portable power station applications. The design incorporates USB PD3.1 controllers TPS26750 and TPD4S480, a 48V extended (...)
Test report: PDF
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| SOT-23-THN (DDF) | 8 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E? forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support. ??????????????