SN74AXCH2T45

正在供貨

具有總線保持電流的 2 位 0.65V 至 3.6V AXC 雙電源總線收發器

產品詳情

Bits (#) 2 Data rate (max) (Mbps) 380 Topology Push-Pull Vin (min) (V) 0.65 Vin (max) (V) 3.6 Vout (min) (V) 0.65 Vout (max) (V) 3.6 Applications JTAG, UART Features Bus-hold, Overvoltage tolerant inputs, Partial power down (Ioff), Vcc isolation Technology family AXC Supply current (max) (mA) 0.023 Rating Catalog Operating temperature range (°C) -40 to 125
Bits (#) 2 Data rate (max) (Mbps) 380 Topology Push-Pull Vin (min) (V) 0.65 Vin (max) (V) 3.6 Vout (min) (V) 0.65 Vout (max) (V) 3.6 Applications JTAG, UART Features Bus-hold, Overvoltage tolerant inputs, Partial power down (Ioff), Vcc isolation Technology family AXC Supply current (max) (mA) 0.023 Rating Catalog Operating temperature range (°C) -40 to 125
VSSOP (DCU) 8 6.2 mm2 2 x 3.1 X2SON (DTM) 8 1.08 mm2 0.8 x 1.35
  • Fully configurable dual-rail design allows each port to operate with a power supply range from 0.65 V to 3.6 V
  • Operating temperature from –40°C to +125°C
  • Glitch-free power supply sequencing
  • Up to 380 Mbps support when translating from 1.8 V to 3.3 V
  • VCC isolation feature
    • If either VCC input is below 100 mV, all I/O outputs are disabled and become high impedance
  • Ioff supports partial-power-down mode operation
  • Compatible with AVC family level shifters
  • Latch-up performance exceeds 100 mA per JESD 78, Class II
  • ESD protection exceeds JESD 22
    • 8000-V human-body model (HBM)
    • 1000-V charged-device model (CDM)
  • Fully configurable dual-rail design allows each port to operate with a power supply range from 0.65 V to 3.6 V
  • Operating temperature from –40°C to +125°C
  • Glitch-free power supply sequencing
  • Up to 380 Mbps support when translating from 1.8 V to 3.3 V
  • VCC isolation feature
    • If either VCC input is below 100 mV, all I/O outputs are disabled and become high impedance
  • Ioff supports partial-power-down mode operation
  • Compatible with AVC family level shifters
  • Latch-up performance exceeds 100 mA per JESD 78, Class II
  • ESD protection exceeds JESD 22
    • 8000-V human-body model (HBM)
    • 1000-V charged-device model (CDM)

The SN74AXCH2T45 is a two-bit non-inverting bus transceiver that uses two individually configurable power-supply rails. The device is operational with both VCCA and VCCB supplies as low as 0.65 V. The A port is designed to track VCCA, which accepts any supply voltage from 0.65 V to 3.6 V. The B port is designed to track VCCB, which also accepts any supply voltage from 0.65 V to 3.6 V. Additionally the SN74AXCH2T45 is compatible with a single-supply system.

The SN74AXCH2T45 device is designed for asynchronous communication between data buses. The device transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level of the direction-control input (DIR). The SN74AXCH2T45 device is designed so the control pin (DIR) is referenced to VCCA.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. If a supply is present for VCCA or VCCB, the bus-hold circuitry always remains active on the A or B inputs respectively, independent of the state of the direction control pin.

This device is fully specified for partial-power-down applications using the Ioff current. The Ioff protection circuitry ensures that no excessive current is drawn from or to an input, output, or combined I/O that is biased to a specific voltage while the device is powered down.

The VCC isolation feature ensures that if either VCCA or VCCB is less than 100 mV, both I/O ports enter a high-impedance state by disabling their outputs.

Glitch-free power supply sequencing allows either supply rail to be powered on or off in any order while providing robust power sequencing performance.

The SN74AXCH2T45 is a two-bit non-inverting bus transceiver that uses two individually configurable power-supply rails. The device is operational with both VCCA and VCCB supplies as low as 0.65 V. The A port is designed to track VCCA, which accepts any supply voltage from 0.65 V to 3.6 V. The B port is designed to track VCCB, which also accepts any supply voltage from 0.65 V to 3.6 V. Additionally the SN74AXCH2T45 is compatible with a single-supply system.

The SN74AXCH2T45 device is designed for asynchronous communication between data buses. The device transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level of the direction-control input (DIR). The SN74AXCH2T45 device is designed so the control pin (DIR) is referenced to VCCA.

Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. If a supply is present for VCCA or VCCB, the bus-hold circuitry always remains active on the A or B inputs respectively, independent of the state of the direction control pin.

This device is fully specified for partial-power-down applications using the Ioff current. The Ioff protection circuitry ensures that no excessive current is drawn from or to an input, output, or combined I/O that is biased to a specific voltage while the device is powered down.

The VCC isolation feature ensures that if either VCCA or VCCB is less than 100 mV, both I/O ports enter a high-impedance state by disabling their outputs.

Glitch-free power supply sequencing allows either supply rail to be powered on or off in any order while providing robust power sequencing performance.
下載 觀看帶字幕的視頻 視頻

技術文檔

star =有關此產品的 TI 精選熱門文檔
未找到結果。請清除搜索并重試。
查看全部 5
頂層文檔 類型 標題 格式選項 下載最新的英語版本 日期
* 數據表 SN74AXCH2T45 2-Bit Bus Transceiver with Configurable Level-Shifting and Bus-Hold Inputs 數據表 PDF | HTML 2016年 11月 16日
應用手冊 原理圖檢查清單 - 使用自動雙向轉換器進行設計的指南 PDF | HTML 英語版 PDF | HTML 2024年 12月 3日
應用手冊 原理圖檢查清單 - 使用固定或方向控制轉換器進行設計的指南 PDF | HTML 英語版 PDF | HTML 2024年 10月 3日
應用手冊 Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) PDF | HTML 2024年 7月 3日
應用手冊 了解 CMOS 輸出緩沖器中的瞬態驅動強度與直流驅動強度 PDF | HTML 最新英語版本 (Rev.A) PDF | HTML 2024年 5月 15日

設計與開發

如需其他信息或資源，請點擊以下任一標題進入詳情頁面查看（如有）。

評估板

5-8-LOGIC-EVM — 支持 5 至 8 引腳 DCK、DCT、DCU、DRL 和 DBV 封裝的通用邏輯評估模塊

靈活的 EVM 設計用于支持具有 5 至 8 引腳數且采用 DCK、DCT、DCU、DRL 或 DBV 封裝的任何器件。
用戶指南: PDF
TI.com 上無現貨
評估板

AVCLVCDIRCNTRL-EVM — 通用 EVM，適用于支持 AVC 和 LVC 的方向控制雙向轉換器件

通用 EVM 設計用于支持單通道、雙通道、四通道和八通道 LVC 和 AVC 方向控制轉換器件。它還能在相同的通道數量下支持總線保持和汽車 Q1 器件。AVC 是具有 12mA 較低驅動強度的低電壓轉換器件。LVC 是 1.65V 至 5.5V 的較高電壓轉換器件，具有 32mA 的較高驅動強度。

用戶指南: PDF | HTML
英語版 (Rev.B): PDF | HTML
TI.com 上無現貨
評估板

AXC2T-SMALLPKGEVM — 適用于 DTM 和 RSW 封裝器件的 AXC2T 小型封裝評估模塊

此 EVM 旨在支持 AXC 和 LVC 系列 DIR 控制雙向器件的 DTM 和 RSW 封裝。AXC 和 AVC 器件屬于低壓方向控制轉換系列，其工作電壓范圍為 0.65V 至 3.6V (AXC) 和 1.2 至 3.6 (AVC)，驅動強度為 12mA。
用戶指南: PDF
TI.com 上無現貨
封裝 引腳 CAD 符號、封裝和 3D 模型
VSSOP (DCU) 8 Ultra Librarian
X2SON (DTM) 8 Ultra Librarian

訂購和質量

包含信息：
  • RoHS
  • REACH
  • 器件標識
  • 引腳鍍層/焊球材料
  • MSL 等級/回流焊峰值溫度
  • MTBF/時基故障估算
  • 材料成分
  • 鑒定摘要
  • 持續可靠性監測
包含信息：
  • 制造廠地點
  • 封裝廠地點

支持和培訓

可獲得 TI 工程師技術支持的 TI E2E? 論壇

所有內容均由 TI 和社區貢獻者按“原樣”提供，并不構成 TI 規范。請參閱使用條款。

如果您對質量、包裝或訂購 TI 產品有疑問，請參閱 TI 支持。??????????????

視頻