ZHCSM89 july 2021 BQ51013B-Q1
PRODUCTION DATA
- 1
- 1 特性
- 2 應用
- 3 說明
- 4 Revision History
- 5 Description (continued)
- 6 Device Comparison Table
- 7 Pin Configuration and Functions
- 8 Specifications
-
9 Detailed Description
- 9.1 Overview
- 9.2 Functional Block Diagram
- 9.3
Feature Description
- 9.3.1 Details of a Qi Wireless Power System and BQ51013B-Q1 Power Transfer Flow Diagrams
- 9.3.2 Dynamic Rectifier Control
- 9.3.3 Dynamic Efficiency Scaling
- 9.3.4 RILIM Calculations
- 9.3.5 Input Overvoltage
- 9.3.6 Adapter Enable Functionality and EN1/EN2 Control
- 9.3.7 End Power Transfer Packet (WPC Header 0x02)
- 9.3.8 Status Outputs
- 9.3.9 WPC Communication Scheme
- 9.3.10 Communication Modulator
- 9.3.11 Adaptive Communication Limit
- 9.3.12 Synchronous Rectification
- 9.3.13 Temperature Sense Resistor Network (TS)
- 9.3.14 3-State Driver Recommendations for the TS/CTRL Pin
- 9.3.15 Thermal Protection
- 9.3.16 WPC v1.2 Compliance – Foreign Object Detection
- 9.3.17 Receiver Coil Load-Line Analysis
- 9.4 Device Functional Modes
-
10Application and Implementation
- 10.1 Application Information
- 10.2
Typical Applications
- 10.2.1
BQ51013B-Q1 Wireless Power Receiver Used as a Power
Supply
- 10.2.1.1 Design Requirements
- 10.2.1.2
Detailed Design Procedure
- 10.2.1.2.1 Using The BQ51013B-Q1 as a Wireless Power Supply: (See )
- 10.2.1.2.2 Series and Parallel Resonant Capacitor Selection
- 10.2.1.2.3 Recommended RX Coils
- 10.2.1.2.4 COMM, CLAMP, and BOOT Capacitors
- 10.2.1.2.5 Control Pins and CHG
- 10.2.1.2.6 Current Limit and FOD
- 10.2.1.2.7 RECT and OUT Capacitance
- 10.2.1.3 Application Curves
- 10.2.2 Dual Power Path: Wireless Power and DC Input
- 10.2.3 Wireless and Direct Charging of a Li-Ion Battery at 800 mA
- 10.2.1
BQ51013B-Q1 Wireless Power Receiver Used as a Power
Supply
- 11Power Supply Recommendations
- 12Layout
- 13Device and Documentation Support
- 14Mechanical, Packaging, and Orderable Information
封裝選項
機械數據 (封裝 | 引腳)
- RHL|20
散熱焊盤機械數據 (封裝 | 引腳)
- RHL|20
訂購信息
10.2.2.3 Application Curves
Figure 10-7 Transition Between Wireless Power and Wired Power (EN1 = EN2 = LOW)
Figure 10-9 Wireless Power Start-Up With VAD = 5 V (EN1 = EN2 = LOW)
Figure 10-8 Transition Between Wired Power and Wireless Power (EN1 = EN2 = LOW)
Figure 10-10 AD Power Start-Up With No Transmitter (EN1 = EN2 = LOW)